Doctor Archive
Thread: Crafting Macro -- for all those asking...
Page 1 of 1
Kieneci
Fri May 21, 2004 6:23 pm
#1
/ui action toolbarSlot00;
/selectDraftSchematic ##;
/pause 05;
/nextCraftingStage;
/nextCraftingStage;
/createPrototype practice no item;
/createPrototype practice no item;
/pause 2;
Repeat this for however many craftingtools you want to use, changing the toolbarSlot## for the next craftingtool. Remember that if you are using different crafting tools (generic, food) the Schematic ## will be different; just open a tool and type in /selectDraftSchematic and go up the numbers until it opens the schematic you want (remember 00 is the first schematic).
You will still have to double-click the resources to add them, so make sure you aren't near anyone that will want to talk to you while you are grinding, or you won't be able to click on the resources fast enough.
NOTE: "Crafting Session has ended" will pop-up every time you finish an item. If you think the macro isn't working, check your XP before and after you run the macro. If you make the macro a loop (by calling the macro again inside the macro) you can stop it by typing /dump
I hope this helps everyone.
LergTHEbutcher
Fri May 21, 2004 6:56 pm
#2
How long would it take using this macro to Master Doctor's Medicine?
Darkknt
Fri May 21, 2004 8:53 pm
#3
Well it took me 2 days 
(Ran out of Wild Wheat, had to wait to harvest more 
)
Also pick the schematic for Adv. BEC, best xp given at Doc level and try to have 5-7 food chem crafting tools, makes the process fly by.
(Ran out of Wild Wheat, had to wait to harvest more )Also pick the schematic for Adv. BEC, best xp given at Doc level and try to have 5-7 food chem crafting tools, makes the process fly by.
TravisC555
Fri May 21, 2004 9:07 pm
#4
Kieneci wrote:
/ui action toolbarSlot00;
/selectDraftSchematic ##;
/pause 05;
/nextCraftingStage;
/nextCraftingStage;
/createPrototype practice no item;
/createPrototype practice no item;
/pause 2;
From what I have tried your highlighted lines didn't work.
Here is the line that I typed and worked in my macro:
/selectdraftSchematic; and /pause 5;
Just thought I'd save a couple of frustrated minds
Kieneci
Sat May 22, 2004 2:33 pm
#5
You have to put a number in ## the number of the schematic. This works fine for me.
TravisC555 wrote:
Kieneci wrote:
/ui action toolbarSlot00;
/selectDraftSchematic ##;
/pause 05;
/nextCraftingStage;
/nextCraftingStage;
/createPrototype practice no item;
/createPrototype practice no item;
/pause 2;
From what I have tried your highlighted lines didn't work.
Here is the line that I typed and worked in my macro:
/selectdraftSchematic; and /pause 5;
Just thought I'd save a couple of frustrated minds
Stephon_Odom
Sat May 22, 2004 4:10 pm
#6
Go to your datapad and find your Schematic number for Advanced Bio Effect Con. (for me its #10) and thats what your put in that "##" space..
Sofaism
Mon May 24, 2004 11:00 am
#7
i tryed this and it loads up the station, i put the materials in, then it says "you are not dancing" or something like that, and ends the crafting... i dunno what is up 
Sofaism
Tue May 25, 2004 6:02 pm
#8
Sofaism wrote:
i tryed this and it loads up the station, i put the materials in, then it says "you are not dancing" or something like that, and ends the crafting... i dunno what is up
bump
Page 1 of 1