Commando Archive

I r spel gud


loosing = losing

You're damage = Your damage

---

Blizzard_1 wrote:

i have a flamethrowe with max 1160 min 560 speed 4.9

is it better to have higher dan max or lower speed, in otehr word it is better a flamethorwer sliced on speed or on damage?

---

As for what makes a better FT depends on the target those that have low HAM's and low or no heat resists I prefer speed sliced. But targets with bigger HAM's and higher resists a harder hitting FT is the way to go as the tick you get of a special is larger. I like using the bigger FT's whilst hunting things like Krayts failing that I do use my LP a lot for blast damage too (goes well with Torso Shot )

Message Edited by freelancerx on 09-11-2004 02:18 PM

---

Blizzard_1 wrote:

is it better to have higher dan max or lower speed, in otehr word it is better a flamethorwer sliced on speed or on damage?

---

---

Blizzard_1 wrote:

i saw it si posible to make krayt Flame Thrower, but does is itusefully or not to to buy one for alot of credits? or just a common flame is the same?

---

It takes 6 IDENTICAL tissues (same serial number) to make one FT, one tissue for making the schematic for the five identical power handlers, and 5 for the power handlers themselves. The Krayt tissues are the best way to reduce theSPEED of the FT, they have a side effect of increasing the max damage of the FT also. Speed is the big issue with FTs though, due to our low attack speed modifiersas of right now. Remember, currently without FS skills, cutting0.5 speed off your FTs speed willcut your special attack speed by around 1 sec.

The schematic also uses one stock, and one blaster rifle barrel so these are also places to use good, looted/rewarditems, IMHO.

Thats whyKrayt FTscost so much, the same amount of tissues can make anywhere from 1 to 6 other weapons so the smith wants to get the same total amount for the single FT ( or other tissue hog).

---

Jhyson-Bria wrote:

---

Blizzard_1 wrote:

i saw it si posible to make krayt Flame Thrower, but does is itusefully or not to to buy one for alot of credits? or just a common flame is the same?

---

It takes 6 IDENTICAL tissues (same serial number) to make one FT, one tissue for making the schematic for the five identical power handlers, and 5 for the power handlers themselves. The Krayt tissues are the best way to reduce theSPEED of the FT, they have a side effect of increasing the max damage of the FT also. Speed is the big issue with FTs though, due to our low attack speed modifiersas of right now. Remember, currently without FS skills, cutting0.5 speed off your FTs speed willcut your special attack speed by around 1 sec.

The schematic also uses one stock, and one blaster rifle barrel so these are also places to use good, looted/rewarditems, IMHO.

Thats whyKrayt FTscost so much, the same amount of tissues can make anywhere from 1 to 6 other weapons so the smith wants to get the same total amount for the single FT ( or other tissue hog).

---

Try 5 identical tissues one for the schematic the other 4 for the Power Handlers used in the FT. So for instance the 11 tissues I looted a few days ago one for the schematic 8 for 2 FT's and 2 scatters. Plus I got the enjoyment of making a rilfeman I know beg me not to butcher the set and make him a T21

Have to agree with good looted barrels or stocks though the IMP Form Fitting the stock is a good addition to a FT.

Message Edited by freelancerx on 09-11-2004 04:15 PM

Unless you're going to one-shot it with a damagethrower, you're best off going with Speed mostly. Gives you a much higher damage-per-second rating. Although, as has been said, a damagethrower will put on a better burn DOT. As a Commando, I always carried one of each, a 4.7 1109 max and a 3.3 880 max.

Message Edited by Lemos on 09-13-2004 04:27 PM

hehe commando 0030 nearly 4 just need to grind for a hour to get it but here we go :

Condition: 947/947 (haven't used yet)
Speed: 2.1
Min: 471
Max: 920

Krayt FFS and a 29% speed slice thanks to bob'the for making me this

off to slay krayts wholesale