CUEmu - Thread Posts

KaliMirchi

Fri Jan 30, 2004 10:23 pm

Hello,

Is there a formula for figuring out what number your draft schematic is? I spend hours to figure it out, only to have it change when I level -- is there a trick to this?

Thanks,

Seenqa

SYRI, Mistress of Melee. Serious Melee Weapons for Intelligent Meleers. It ISN'T always about Damage!

I've been a successful melee combatant since launch. I know melee.

Short ride SE of Coronet. 804 - 5348

walcyradiant

Fri Jan 30, 2004 10:58 pm

#2

In your datapad, start counting from left to right, top to bottom... and start w/ zero. Also, gotta skip anything you can't actually make w/ the crafting tool you are using. To further complicate things, if you go near a crafting station (public/private/droid), it'll increase the number of things you can make w/ a crafting tool and thus change the number of the schematic you want. If it's not straight forward counting and that's the one... what i found was to guess a number, see what popped up and check if it's low/high compared to what i was aiming to make. Good luck. =)

Walcy

Back visiting during a free trial.

Last account cancelled as of 12/1/05
Thanks for the memories.

Cylenthia_Tavishaun

Fri Jan 30, 2004 11:01 pm

#3

1+1=2 is pretty much the formula.

If you are using generic crafting units and you are away from a crafting station just go into your schematic data and count from the top left to right and skip any schematic that you can't make with whatever crafting tool you are using. (Remember that the first schematic is 00). Once you get used to the setup of how to count them...it still sucks.

Cylenthia Tavishaun
Master Brawler | Master Swordsman | Master Pikeman
Warrant Officer I, Imperial Army
Daughters of Allya (SHE)

KaliMirchi

Sat Jan 31, 2004 9:31 am

#4

Thanks for the help guys.... not sure what you mean - left to right -- so, you'll be going from generic to clothing to weapons for instance? For example the first item listed in generic would be 1 the first item listed in clothing will be 2 and the first item listed in weapons will be 3?

Seena

SYRI, Mistress of Melee. Serious Melee Weapons for Intelligent Meleers. It ISN'T always about Damage!

I've been a successful melee combatant since launch. I know melee.

Short ride SE of Coronet. 804 - 5348

KaliMirchi

Sat Jan 31, 2004 9:49 am

#5

LOL omg -- sorry, I didn't read carefully -- missed the datapad part -- got it now. duh. Thanks a bunch for all your help : )

Seena

SYRI, Mistress of Melee. Serious Melee Weapons for Intelligent Meleers. It ISN'T always about Damage!

I've been a successful melee combatant since launch. I know melee.

Short ride SE of Coronet. 804 - 5348

morkill

Sun Feb 01, 2004 6:03 am

#6

KaliMirchi wrote:

Hello,

Is there a formula for figuring out what number your draft schematic is? I spend hours to figure it out, only to have it change when I level -- is there a trick to this?

Thanks,

Seenqa

For finding your schematic number, use this.

___________________________________________________________________________________

From Candleman:

Create a macro and name it whatever you want. I call mind Sel. You can name it Finder iguess.

/ui action toolbarSlot00
/sel 147

That is it. First line selects the crafting tool you should have in slot00. The second line selects the item 147 in your Data Schmatics(in your datapad). This is the last one i had to do so your number will most likely be different. Each item that you can make is in your data Schmatics tab of your datapad. They all are numbered 0 - XXX. We don't know what that number is. That is why we run this macro. You will need to run the macro. If you arn't close, changethe /sel # and try again, and again, and again. sometimes it takes several tries. Remember that you see more of them when you are near a crafting stations. Remember your number, you will need it in the rest of the macros.

Artisan Archive

Thread: A little help with macros