Armorsmith Archive
Thread: Can Someone answer this Advanced Compo Segment Question I have?
Page 1 of 1
paulyboy64
Tue Aug 10, 2004 1:00 pm
#1
Hey If anyone could tell me what this segment would produce in terms of Composite armor, I would greatly Appreciate it 
My first time making Composite and this is my first Advanced composite segment as test run.
My first time making Composite and this is my first Advanced composite segment as test run. This segment has two layers of Stun and one layer of Blast. Should I just use one armor layer of each since there are 3 slots? For Example: should I use 1Kinetic Armor Layer(should I even use Kinetic Layer?), 1Stun Armor Layer and 1 Blast Armor Layer?:
Advanced Composite Segment:
Base Effect 23%
Integrity 1110
Health/Action Encumberance 62
Mind Encumberance 65
Blast 10%
Electrical 19%
Stun 22%
AegolinAdaron
Tue Aug 10, 2004 1:41 pm
#2
paulyboy64 wrote:
Hey If anyone could tell me what this segment would produce in terms of Composite armor, I would greatly Appreciate it
This segment has two layers of Stun and one layer of Blast. Should I just use one armor layer of each since there are 3 slots? For Example: should I use 1Kinetic Armor Layer(should I even use Kinetic Layer?), 1Stun Armor Layer and 1 Blast Armor Layer?:
Advanced Composite Segment:
Base Effect 23%
Integrity 1110
Health/Action Encumberance 62
Mind Encumberance 65
Blast 10%
Electrical 19%
Stun 22%
When using high quality resources for your final combine, I would expect for your armor something like this:
Base 58%
Blast 69%
Electrical 77%
Stun 22%
Your final results will entire to a large extent on the quality of your resources.
And if it is a chestplate you make:
HAM = 285/120/85
What layers to use depends entirely on what you are trying to achieve. Personally, I would try to get the base resist higher.
Check the guide to armorsmithing on the top of this forumfor further info.
Emily
NiBorg
Tue Aug 10, 2004 1:43 pm
#3
It would greatly depend on the resources you use for your final product. Using the resources I have on hand I personally would get approximately 57% base, 67% blast, Max elec, and of course 22% stun. From the looks of it if you were to experiment your base more in your segment and not in special as your elec is way up there you could easily get a another 5-8 points in the final base. I would recommend using this tool posted in the AS forum on swgcraft.com and tinker with your experiments to see where you are now and see where you wish to be.
http://www.swgcraft.com/forum/showthread.php?t=10294
paulyboy64
Tue Aug 10, 2004 6:45 pm
#4
Yeah I did put alot in the Special Resists. Ill put more pts in the Base. Thanks for the info guys appreciate it.
Fobi
Tue Aug 10, 2004 10:18 pm
#5
yea i got the same quetions but heres my stun armor with 3 stun layors, 29% base 60/60/62 Stune 30% E 8% what kinda armor is would this make with your resources you think?
NiBorg
Wed Aug 11, 2004 2:56 pm
#7
I would again say to try that tool, it's very usefull and almost completely accurate, the only thing that's not 100% from my experience when i use it is the HAM. I use it as a prelim to see how good or bad a new metal or gem will effect my layers before i go nuts getting something that is only 5-10 points difference.
Page 1 of 1