Architect Archive
Thread: POST PATCH FUSION GENERATOR EXTRACT RATES?
Page 1 of 1
SinisterFiend
Sat Nov 15, 2003 6:58 am
#1
What is everyone getting? I'm get'n 13 extract from newly made Fusion Gen's.
BetaZoob
Sat Nov 15, 2003 7:13 am
#2
13 is its base rate.
I have a 16 from just a day pre-patch. I'll try making one today (I get good 92% efficiency OMUs and mechanisms) and see what happens.
SinisterFiend
Sat Nov 15, 2003 7:32 am
#3
This sucks, cause I sold all my fusion gen's to make new ones. *frowns*. How about everyone else? What's your rates?
no_bargain
Sat Nov 15, 2003 7:35 am
#4
I have a 17 schematic I made pre-patch.. haven't even checked if it still worked. Hmmm..
ImLucas
Sat Nov 15, 2003 7:52 am
#5
Fusions are currently bugged...
In the schematic, it has a section listed to allow us to experiment the efficiency(like on harvs), but it's listed under the main category of "misc" instead of "experimental efficiency".
This causes the experiment bar to not show up.
However, I did make a 14 BER fusion... so if the current formulas hold true, if they fix the experiment bar, we should be able to make a 17 BER fusion.
What does concern me is this...
Are fusions being held to the same "experimental maintenance" rates as our harvs?
I don't think it would be a nice thing for a standard fusion(rate 13) to have a maintenance rate of a fully experimented heavy...
In the schematic, it has a section listed to allow us to experiment the efficiency(like on harvs), but it's listed under the main category of "misc" instead of "experimental efficiency".
This causes the experiment bar to not show up.
However, I did make a 14 BER fusion... so if the current formulas hold true, if they fix the experiment bar, we should be able to make a 17 BER fusion.
What does concern me is this...
Are fusions being held to the same "experimental maintenance" rates as our harvs?
I don't think it would be a nice thing for a standard fusion(rate 13) to have a maintenance rate of a fully experimented heavy...
ArchitectHaven
Sat Nov 15, 2003 8:26 am
#6
I'm not quite sure why we won't be able to make 19 rated fusions....I can easily get +6 with an ore mining unit...did they change the schem to not use this now?
_-ArchAngel-_
Sat Nov 15, 2003 9:31 am
#7
Fusions get a maintenance increase like Heavy Harvesters, but if I'm not mistaken, it starts at ER 13, instead of ER 7.
ZenDragonMLS
Sat Nov 15, 2003 9:53 am
#8
Pre-patch I made some +57% Ore Mining Units and got rate 16 fusions.
Post-patch (last night) I made some +87% Ore Mining Units that claimed "rate=6" in their examine. I made one into a fusion and got a rate 13 fusion. I just checked that deed this morning after the server reset and it still says rate 13. I don't want to try it again until I hear more about what's going on.
Is it safe to make a heavy mineral with these Ore Mining Units?
Post-patch (last night) I made some +87% Ore Mining Units that claimed "rate=6" in their examine. I made one into a fusion and got a rate 13 fusion. I just checked that deed this morning after the server reset and it still says rate 13. I don't want to try it again until I hear more about what's going on.
Is it safe to make a heavy mineral with these Ore Mining Units?
LemyDaBigHairyWookie
Sat Nov 15, 2003 12:01 pm
#9
the best i've done post patch was 14 with a 92% ore unit... my heavys are coming out with 11-13 rate depending on experimentation success... nothing like a 3 block amazing success getting wiped out by a 2 crit failsto put a damper on the Extract rate
Neilla
Sat Nov 15, 2003 4:59 pm
#10
I just checked my BER 16 fusions. The surcharge was only 6 credits per hour.
BetaZoob
Sat Nov 15, 2003 5:10 pm
#11
It's beginning to sound like the base rate of fusions have been decreased dramatically, so that when you include a +6 OMU into it, it is only getting you into 13s or 14s.
Page 1 of 1